manualshive.com logo in svg

ACV ACVMax Touch, Installer'S Handbook, Page: 3 / 48

Share
Download
ACV ACVMax Touch Installer'S Handbook Download Page 3

NOTE

This manual contains important information for the installer, with respect to the installation and 

set-up of the boiler.
This manual is only available on the Internet. Please check for the latest revision on our web-

site (www.acv.com).

We accept no liability should any damage result from the failure to comply with 

the instructions contained in this technical manual.

Essential recommendations for safety

• 

 It is prohibited to carry out any modifications to the appliance without the 

manufacturer’s prior and written agreement.

• 

 The appliance must be set up by a qualified installer, in accordance with 

applicable standards and regulations.

• 

 The installation must comply with the instructions contained in the boiler's 

installation manual and with the standards and regulations applicable to 

heating systems. 

• 

 Failure to comply with the instructions in this manual could result in personal 

injury or a risk of environmental pollution.

• 

 The manufacturer declines all liability for any damage caused as a result of 

incorrect installation or in the event of the use of appliances or accessories that 

are not specified by the manufacturer.

Essential recommendations for the correct operation of the appliance

• 

 To guarantee the correct operation of the installation, it is essential to carry out 

the adjustments in accordance with the instructions in this manual.

• 

 In order to ensure that the appliance operates correctly, it is essential to inspect 

and service the boiler every year.

• 

 Faulty parts may only be replaced by genuine factory parts.

General remark

• 

 The availability of certain models as well as their accessories may vary according 

to markets.

• 

 The manufacturer reserves the right to change the technical characteristics 

and features of its products without prior notice. Please check for an updated 

version of this manual in the documentation page on the website www.acv.com.

3

Installer's Handbook (Evo) - 660Y3000 • A

EN

If you smell gas:

 - 

Immediately isolate the gas supply.

 

- Open windows and doors to ventilate the area.

 

- Do not use any electrical appliances and do not operate any switches.

 - 

Immediately notify your gas supplier and/or your installer.

IMPORTANT INSTRUCTIONS - READ BEFORE PROCEEDING

Essential recommendations for safety

•   This document is intended to be used by a factory-trained and qualified 

heating contractor or service technician only. Read all instructions within 

this document and within the concerned appliance's Installation, Operation 

and Maintenance Manual before proceeding. 

•  It is recommended to follow the procedures in the steps given. Skipping 

or missing procedural steps could result in severe personal injury, death or 

substantial property damage.

•   This appliance can be used by children aged from 8 years old and above 

and persons with reduced physical, sensory or mental capabilities or lack 

of experience and knowledge, if they have been given supervision or 

instruction concerning the use of the appliance in a safe way and understand 

the hazards involved.

•  Children should be supervised to ensure that they do not play with the 

appliance.

APPLICABILITY

This manual is applicable to Evo appliances manufactured from 2022 and equipped with an  

ACVMax Touch interface. 

For appliances equipped with the other ACVMax interface, please refer to the 

previous version of the  Installer's Handbook (660Y2900).

RECOMMENDATIONS

Summary of Contents for ACVMax Touch

















































Reviews:

No comments