manualshive.com logo in svg

ACV ACVMax Touch, Installer'S Handbook, Page: 16 / 48

Share
Download
ACV ACVMax Touch Installer'S Handbook Download Page 16

16

Installer's Handbook (Evo) - 660Y3000 • A

EN

DHW Setting

DHW Setting

DHW Operation 

Enabled

Demand 

Sensor

DHW Boost 

Enabled

DHW Boiler Setpoint 

75°C

DHW Setpoint 

60°C

DHW on Differential 

3°C

DHW Boiler Setpoint 

is the fixed appliance setpoint temperature during a domestic hot water call when the Thermostat option 

is chosen in Demand Type. 

This function is not applicable to Evo models. The screen is displayed and available, but any change made here will have no effect.

DHW Setpoint

 is the domestic hot water storage setpoint temperature when the Sensor option is chosen in Demand Type. 

Touch the 

LEFT

 or 

RIGHT

 soft keys to adjust the DHW Setpoint then touch the 

OK

 key to store the setting.

Default: 60°C

DHW On Differential

 sets how far the DHW storage temperature must fall below the DHW Storage Setpoint to create a domestic 

hot water call when the Sensor option is chosen in Demand Type. The domestic hot water call will end when the DHW storage 

temperature rises above the DHW Storage Setpoint. 
Touch the 

LEFT

 or 

RIGHT

 soft keys to adjust the DHW On Differential then touch the 

OK

 key to store the setting.

Default: 3°C

DHW

Boiler Setpoint

75°C

35°C

87°C

DHW Setting

DHW Operation 

Enabled

Demand Sensor

DHW Boost 

Enabled

DHW Boiler Setpoint 

75°C

DHW  Setpoint 

60°C

DHW on Differential 

3°C

DHW Setpoint

60°C

20°C

75°C

DHW Setting

DHW Operation 

Enabled

Demand Sensor

DHW Boost 

Enabled

DHW Boiler Setpoint 

75°C

DHW Setpoint 

60°C

DHW on Differential 

3°C

DHW On Differential

3°C

2°C

10°C

•  The appliance setpoint is automatically set to the DHW Se DHW Storage adder when the Sensor option 

is chosen in DHW demand.

•  Increase this value up to at least 70°C to enable the DHW Boost function

The DHW on differential setting greatly affects the production of domestic hot water. A low setting could result in a rapid 

response to a domestic hot water call resulting in a potential scald hazard. It is strongly recommended that the installer 

use a thermostatic mixing valve on the hot water outlet of the Indirect Water Heater. Failure to comply could result in 

severe personal injury, death, or substantial property damage.

DHW Storage Adder

 is used to compute the appliance setpoint when the Sensor option is chosen in Demand Type. The appli-

ance setpoint will be DHW Se DHW Storage Adder for a domestic hot water call. 
Touch the 

LEFT

 or 

RIGHT

 soft keys to adjust the DHW Storage Adder then touch the 

OK

 key to store the setting.

Default: 15°C

DHW Setting

Demand Sensor

DHW Boost 

Enabled

DHW Boiler Setpoint 

75°C

DHW Setpoint 

60°C

DHW on Differential 

3°C

DHW Storage Adder 

15°C

DHW Storage Adder

15°C

5°C

30°C

DESCRIPTION AND OPERATION

Summary of Contents for ACVMax Touch

















































Reviews:

No comments