ActivMedia Robotics MOBILEROBOTS Team AmigoBot-SH Operation Manual Download Page 56

Page: 56 / 61

Console mode:

1. Power

off.

2. Attach a cross-over serial cable between your PC and the serial port on the device.
3. Start

minicom

(Linux),

HyperTerminal

(Windows®) or comparable serial console on

your PC.

4. Serial settings are 115,200 baud, 8 bits, one stop, no parity, and hardware

handshaking.

5. Hold in the test button and power the device.
6. Press

the

Return

key to get the

Local>

prompt

7. Type:

8. set ip address aa.bb.cc.dd (aa.bb.cc.dd is the device IP address)

9. set ip router aa.bb.cc.dd (aa.bb.cc.dd is the gateway IP address)

10. set ip subnet aa.bb.cc.dd (aa.bb.cc.dd is the subnet IP mask)
11. save

12. init

13. exit

14. Restart the device

Webpage

1. Start web browser and access

http://192.168.1.xx

(last two digits depend on

device’s factory setting, typically .11)

2. The default password is

‘access’

3. Select

Configure TCP/IP

4. Change the fields for the IP address, subnet mask, and gateway
5. Click

Submit

Restart the device

Peer-to-Peer Networking

If you don’t have an established LAN or access to the wireless network, you may operate

your robot wirelessly directly from a PC that contains wireless Ethernet in what is known as
peer-to-peer mode.
1. From console mode (see above), at the

Local>

prompt

2. Type:

3. set enet mode adhoc

4. save

5. init

6. exit

7. Restart the device

1. Or from the webpage (access as above)

Select

Configure WiFi

3. Choose

Ad-hoc

from the

Mode

4. Submit

Restart the device

Summary of Contents for MOBILEROBOTS Team AmigoBot-SH






























































Search results

Summary of Contents for MOBILEROBOTS Team AmigoBot-SH

Reviews:

Related manuals for MOBILEROBOTS Team AmigoBot-SH

Brands by name

Popular brands

ActivMedia Robotics MOBILEROBOTS Team AmigoBot-SH, Operation Manual

Search results

Summary of Contents for MOBILEROBOTS Team AmigoBot-SH

Reviews:

Related manuals for MOBILEROBOTS Team AmigoBot-SH

Brands by name

Popular brands