manualshive.com logo in svg

ACS ALCOLOCK LR, Installation Manual

Share
Download
ACS ALCOLOCK LR Installation Manual Download Page 62

ALCOLOCK LR

61

24.0    Tampering

This section will outline signs and examples of tampering as well as the tamper 

reporting procedure.

24.1     Signs of tampering

If there are signs of tampering (indicated by an HS Recall or during routine vehicle 

inspection), inspect the entire ECU wire harness for cuts and tamper seal removal. 

Check the ECU and the HS for any signs of tampering.

Look for the following:

• 

Cut or stripped wiring 

• 

Damaged seals

• 

A 

VOID

 marking in the place of a removed seal

24.2     Examples of tampering – before and after 

The following are areas of the interlock where tampering is likely to take place. 

The left side shows areas where tampering has not occurred. The right side shows 

those same areas after tampering has occurred.

 ATTENTION!

 Instances of tampering are not limited to these areas, and you 

must check the entire device wiring assembly and all components for signs of 

tampering.

Before tampering

After tampering 

Tamper resistant label over wiring:

NOTE: Look for any traces of the VOID 

marking left under a removed seal.

Tamper resistent label over vehicle 

grounding:

Summary of Contents for ALCOLOCK LR









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands