manualshive.com logo in svg

ACS ALCOLOCK LR, Installation Manual

Share
Download
ACS ALCOLOCK LR Installation Manual Download Page 49

Installation Manual

48

ATTENTION!

•  Complete the HS removal procedure on the HS display before performing an ITE 

removal transaction

•  Before beginning the procedure ensure that there is sufficient ventilation for 

vehicle exhaust fumes. Failure to do so may cause injury

•  Before beginning the procedure ensure that the vehicle is in the park or neutral 

position, with parking brake engaged, to prevent the vehicle from moving

USING HANDSET BUTTONS:

 

HS screen options will appear at the bottom of the display (at the left, right 

or bottom-centre).

Press the 

left, right or bottom navigation button to select a corresponding 

screen-command option.

NOTE:

• 

To access the HS removal procedure, a daily service code is required – obtained from ITE 

• 

To exit the procedure at any time, press and hold the bottom button to select 

Exit

• 

Remaining in any screen for 5 minutes will exit the procedure

22.2     Performing the HS removal procedure

1.  Press any navigation button to power up the device.

Wait… 

is briefly displayed as the HS powers up.

Summary of Contents for ALCOLOCK LR









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands