manualshive.com logo in svg

Acom 700S, Operating Manual, Page: 26 / 30

Share
Download
Acom 700S Operating Manual Download Page 26

26

26

      

Fig. 5-6 Menu: RESTORE DEFAULT SETTINGS                        

6.  REMOTE CONTROL

6-1.  General information

The ACOM 700S may be controlled remotely by the RS232 port.

The ACOM 700S RS232 interface protocol is available on www.acom-bg.com.

7.  MAINTENANCE

W A R N I N G  

 HIGH VOLTAGE!

The mains line voltage and a high DC voltage of up to 500V 

inside the ACOM 700S amplifier are both LETHAL! For

your safety, pull the amplifier power plug out of the mains 

wall outlet and WAIT AT LEAST three minutes EACH TIME 

BEFORE servicing the amplifier!

7-1.  Periodic maintenance; general checks and cleaning

a)  Periodically  (but  at  least  once  per  year)  check  all  connections,  contact  cleanliness  and  the 

tightening of all connectors, in particular the coaxial ones.

Check the integrity of the cables, in particular when they are layed on the floor. Check also if the cables 

are secured well in the area where they come out of the connector body.

Pay particular attention to the mains plug and the wall outlet – if you have any doubts consult with an 

electrician.

 

Summary of Contents for 700S































Reviews:

No comments