Acom 700S Operating Manual Download Page 12 | Manualshive

Page: 12 / 30

Acom 700S Operating Manual Download Page 12

12

12

Fig. 3-1 Front panel

c) 6 functional buttons keypad for manual (local) control of the amplifier. The function of each

button is indicated on the display above it. Depending on the displayed menu, the buttons may

have different functions.

d) A color display showing the operating information.

3-3.

Initial turning on

In order to start up the amplifier, push and hold the POWER button on the front panel for one or two

seconds - аbout ten seconds later (boot sequence) the display will flash and show the

basic screen

with

the amplifier information - Fig. 3-2.

The amplifier may start either in Stand-by or in Operate mode – see S. 5-4 USER PREFERENCES -

AUTO OPERATE.

3-4.

Basic screen

There are 9 information areas on the basic screen:

a) Information area for the frequency band – the edges of the currently selected BAND are

displayed.

If the amplifier doesn’t receive any operating frequency data from CAT or via RS232, it will switch to the

last used band.

«
...
10
11
12
13
14
...
»

Summary of Contents for 700S































Reviews:

No comments