ACOEM ATD- 300 User Manual Download Page 46 | Manualshive

Page: 46 / 53

background image

For a safe installation the requirements below must be followed:

● The wall has to be designed to support the weight of the pod/bracket and all the

additional load entailed by the pod installation and external factor (wind, snow….)

● Each fixation point has to be able to support at least 25kg
● The fixation has to be adapted to the support (concrete, wood....)
● The fixation must be chosen to resist to climatic and environmental constraints
● The fixation must be tight enough to prevent any movement
● Connect the Ethernet cable on the pod and fix the Ethernet cable on the mast to avoid

any mouvement

ACOEM

|

ATD-300/ATD-301

|

User Manual FW 1.0.0.4 46

«
...
44
45
46
47
48
...
»

Summary of Contents for ATD- 300






















































Reviews:

No comments

Related manuals for ATD- 300

Brand: G-Tek Pages: 28

Brand: Campbell Hausfeld Pages: 12

Brand: Campbell Hausfeld Pages: 44

Brand: Danfoss Pages: 28

CONCORD Express

Brand: GE Interlogix Pages: 32

Brand: U-Prox Pages: 3

Brand: Bose Sicilia Pages: 24

Brand: Hanshen Pages: 18

Brand: ESP Pages: 4

BugHunter Professional BH-03 Expert

Brand: i4Technology Pages: 25

Brand: Vivotek Pages: 91

Brand: Idis Pages: 37

Brand: Magmaweld Pages: 136

Brand: Qlight Pages: 4

Brand: EDIFIER Pages: 8

Brand: ITALIAN STAGE Pages: 18

Brand: iWeld Pages: 10

Smarty 4X P Series

Brand: Salda Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands