manualshive.com logo in svg

Acer Veriton 3600G, Service Manual

Share
Download
Acer Veriton 3600G Service Manual Download Page 83

74

Chapter 3

Removing the System Main board

1.

See “Removing the Housing Cover” on page 63

2.

See “Removing the FDD and DVD Frame” on page 65

3.

See “Removing the AGP VGA Card” on page 64

4.

See “Removing the LAN Card” on page 65

5.

Before you remove the system main board, make sure that all cables connected to the main board are 
removed.

6.

Remove the eight screws as shown here then detach the main board from the lower case.

Removing the I/O Port Bracket

1.

See “Removing the Housing Cover” on page 63

2.

See “Removing the FDD and DVD Frame” on page 65

3.

See “Removing the AGP VGA Card” on page 64

4.

See “Removing the LAN Card” on page 65

5.

See “Removing the System Main board” on page 74

6.

Release the I/O port bracket from the housing and then detach it from the housing..

Summary of Contents for Veriton 3600G




























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands