manualshive.com logo in svg

Acer Veriton 3600G, Service Manual

Share
Download
Acer Veriton 3600G Service Manual Download Page 32

Chapter 1

23

Hardware Specifications and Configurations

NOTE: 

The BIOS can be overwritten/upgraded using the FLASH utility (AWDFLASH.EXE).

Processor

Item

Specification

Type

Intel® Pentium 4 Northwood FSB400/533/800MHz; Intel® Pentium 4 Prescott 
3.4GHz-4.4GHz; Intel® Celeron 2.0-3.0GHz and above

Slot Socket 

mPGA478

Speed

Internal: 1.4~3.2GHz+
External: 533/800MHz Data Bus Frequency for Springdale-G/Springdale PE.

Minimum operating speed

0 MHz (If 

Stop CPU Clock in Sleep State the BIOS Setup 

is set to 

Enabled

.)

Voltage

Processor voltage can be detected by the system without setting any jumper.

BIOS

Item 

Specification

BIOS code programmer

Award

BIOS version 

V6.0

BIOS ROM type

Intel FWH SST 49LF004-33-4C-NH

BIOS ROM size 

4MB

Support protocol

PCI 2.1, APM1.2, DMI 2.00.1, E-IDE, ACPI 1.0, ESCD 1.03, ANSI ATA 3.0, PnP 
1a, Bootable CD-ROM 1.0, ATAPI

Boot from CD-ROM feature

Yes

Support to LS-120 drive

No

Support to BIOS boot block feature Yes

BIOS Hotkey List

Hotkey

Function

Description

c

Enter BIOS Setup Utility

Press while the system is booting to enter BIOS 
Setup Utility. 

a

+

 

o

Enable hidden page of BIOS Setup Utility

Press in BIOS Setup Utility main menu screen, 
the Advanced Options menu then appears. 
The items on the Advanced Options menu are: 
Memory/Cache Options
PnP/PCI Options
Chips Options

Summary of Contents for Veriton 3600G




























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands