Acer Veriton 3600G Service Manual Download | Manualshive

Page: 107 / 155

background image

98

Chapter 3

Removing the Power Supply

1.

See “Removing the Housing” on page 89. (Remove the left panel only)

2.

Disconnect the FDD power connector from the FDD drive and the HDD power connector from the HDD.

3.

Disconnect the CD-RW power connector from the CD-RW drive and DVD-ROM power connector from the
DVD-ROM drive.

4.

Disconnect the main power connector and 12 Volt. power connector from the main board. Remove the
four screws that hold the power supply to the housing and detach the power supply from the housing

..

Removing the LED Activity Indicators With Power Switch Cable Module

1.

See “Removing the Housing” on page 89

2.

See “Removing the Front Panel” on page 89

3.

Release the latches as shown here and then press the LED activity indicators with power switch cable
module and then detach the whole module from the housing .

4.

Disconnect the power LED, hard disk drive activity LED , network activity and power swtich cables from
the main board.

«
...
105
106
107
108
109
...
»

Summary of Contents for Veriton 3600G




























































































































































Reviews:

No comments

Related manuals for Veriton 3600G

Brand: Gateway Pages: 278

Brand: TES Pages: 45

Brand: Oval Pages: 18

Brand: Uplift Desk Pages: 2

Brand: Jupiter Pages: 2

Brand: Acer Pages: 20

Brand: Acer Pages: 3

Aspire Z5610 Series

Brand: Acer Pages: 2

Brand: Acer Pages: 4

Brand: Acer Pages: 52

Chromebase CA24I2

Brand: Acer Pages: 31

Brand: Acer Pages: 29

Aspire Z5600 Series

Brand: Acer Pages: 32

Brand: Acer Pages: 3

Brand: Acer Pages: 91

Brand: Acer Pages: 110

Brand: Acer Pages: 108

Brand: Acer Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands