Chapter 2
37
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press
F2
during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press
F2
to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
P h o e n i x S e c u r e C o r e ( t m ) S e t u p U t i l i t y
M a i n
C P U Ty p e :
C P U S p e e d :
I D E 0 M o d e l N a m e :
I D E 0 S e r i a l N u m b e r :
:
ATA P I M o d e l N a m e :
S y s t e m B I O S Ve r s i o n :
V G A B I O S Ve r s i o n :
K B C Ve r s i o n :
S e r i a l N u m b e r :
A s s e t Ta g N u m b e r :
P r o d u c t N a m e :
M a n u f a c t u r e r N a m e :
U U I D :
I D E 1 M o d e l N a m e :
I D E 1 S e r i a l N u m b e r :
I n t e l ( R ) C o r e ( T M ) 2 D u o C P U
T 8 4 0 0 @ 2 . 2 6 G H z
2 . 2 6 G H z
X X X X X X X X X X X - ( X X )
X X X X X X X X
X X X X X X X X X X X - X X X X X - X X X X - ( X X )
V X . X X
X X - X X X X X X X X X . X X X . X X X . X X X . X X X X X X
X X . X X
X X X X X X X X X X X X X X X X X X X X X X X
N o n e
A s p i r e 8 7 3 0 G
A c e r
X X X x X x X X - x X x X - X X x x - x X X x - x X X x X X x X x x X X
X X X X X X X X X X X - ( X X )
X X X X X X X X
F1
Esc
H e l p
E x i t
S e l e c t I t e m
S e l e c t M e n u
C h a n g e Va l u e s
S e l e c t S u b - M e n u
-/+
Enter
F9
F10
S e t u p D e f a u l t s
S a v e a n d E x i t
I n f o r m a t i o n
S e c u r i t y
B o o t
E x i t
System Utilities
Chapter 2
Summary of Contents for Aspire 8735
