manualshive.com logo in svg

Access Control Solutions Eternity 4, Owners Manual And Software Manual

Share
Download
Access Control Solutions Eternity 4 Owners Manual And Software Manual Download Page 8

Page 8 of 56 

  
 
                                     MORTISE APPLICATIONS WITH THE ETERNITY 4 LOCK 
 
 
NOTE:  

When ordering an E4 for a mortise application it is important to order the lock factory equipped for that use.  

The E4 lock must have shallow back mounting plates installed instead of the standard back plates as well as a longer 
power cable when used with the mortise latch. While it is possible to refit the shallow E4 back plates in the field, the 
standard power cable is very short and is soldered in place inside the lock. When carefully placed the standard cable 
will usually reach, but the installation is much more difficult. In addition, there are a number of small springs and 
pins that are likely to fall out of place when the back plates are interchanged. The original factory warranty will be 
void if a field retrofit is attempted on an E4 lock. If a retrofit to mortise use of an existing standard E4 lock is desired, 
contact Uaccess LLC technical support at 972-492-0752 for assistance. 

 

Unlike the E4 itself, the mortise latch must be ordered either left or right handed. This refers to the swing direction and 
hinge locations of the door. If in doubt about which mortise type you need, contact your distributor or a factory 
representative for advice. While the E5 lock does not need modification for mortise use, like the E4 the mortise used 
must be ordered as either left or right handed. If in doubt as to which you need, contact your dealer or Uaccess LLC 
technical support at 972-492-0752

 

Mortise Lock 'Handed' Definitions 

Door Swings In 

Left Handed Mortise                                            

Right Handed Mortise

 

 

 This side is Outside view of the door  

(Keypad and iButton side of door) 

************************************************* 

Right Handed Mortise

                                            

Left Handed Mortise

 

Door Swings Out 

 

 This side is Outside view of the door  

(Keypad and iButton side of door)

 

Summary of Contents for Eternity 4

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands