manualshive.com logo in svg

Access Control Solutions Eternity 4, Owners Manual And Software Manual

Share
Download
Access Control Solutions Eternity 4 Owners Manual And Software Manual Download Page 49

Page 49 of 56 

 

Section 3 Non-software Guide 

 
This section is for the use of either the Eternity 4 or Eternity 5 without using PC software.  If you use the software to setup 
the lock, then you can no longer use the keypad to program the E4/E5 without resetting the lock.  Likewise, if you use the 
keypad and master code to manually setup the lock, you cannot use the software with the lock unless you reset and do a 
new lock setup from scratch.  
Note: All E4 and E5 

models can be programmed manually using the keypad. All E4 models can be programmed using PC 

software or manually with the keypad, however only certain E5 models can be programmed by either method. Specific 
model information can be found in the software portion of the manual.

 

I.

 

General Information:  

•

 

Exit Setting:

 Enter * to exit the setting procedure, or wait for 10 seconds 

•

 

Low Battery warning:

 When the voltage drops below 4.8V, after entering a valid code, the red LED will flash and beep 

five times. 

•

 

Unlock:

 Green light flashing twice and Beeps twice. 

•

 

Lock:

 Red Light flashing twice, and beeps twice. 

•

 

Reset:

 To set the lock back to factory default settings, press and hold the reset button for about 10 seconds. When the 

LED starts flashing, release the reset button and press the '#' key while the LED is still flashing. The lock will beep 3 
times, indicating the reset was successful. (The reset button is located below the battery holder.) This procedure applies 
to lock firmware v8.6. 

Other firmware versions may require a slightly different procedure.

 Contact Technical 

assistance at 972-492-0752 if required. 

 

The reset button for the Eternity 4 is shown below. 

 
 
 
 
 
 
 
 
 
 
 
 

The reset button for the Eternity 5 is shown below. 

 
 
 
 

 

 
 
 
 
 

II.

 

Manufacture Default Setting: 

•

 

Daylight Saving:

 Disabled 

•

 

    Auto unlock/lock:

 Disabled 

•

 

Default Programming Code:

 123456 

•

 

Lock Mode:

 Storehouse 

 

E4 Reset button 

Eternity 5 
Reset Button 

Summary of Contents for Eternity 4

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands