Access Control Solutions Eternity 4 Owners Manual And Software Manual Download Page 6

Page: 6 / 56

Page 6 of 56

III.

General Lock Spec

This page shows the similar specifications of the Eternity 4 and Eternity 5.

Keypad

: 12 key weather-resistant numeric keypad

Keypad Functions

: Permanent codes, Temporary codes, one-time service codes

Power Supply

: 4 standard AA batteries with an inside battery pack for all weather conditions

Power Supply Life Expectancy

: 10,000 operations, low battery warning when system drops below 4.8 volts

Memory Retention

: Flash memory never loses memory even without power (except current time and date)

Programming / Communication Method

: iButton key-fob, no annoying wires

Functions

: Timed lock functions, (automatically unlock or lock), fully programmable exception dates (holidays),

temporary dates, and time restrictions for keypad code users and iButton key-fobs.

Finishes

: Brushed Chrome or Brushed Brass. (Brushed brass E5 only)

Handles

: Reversible Levers, inner and outer

Audit Trail

: 3000-event audit trail.

Users

: 299, can be a mix of keypad codes and iButton key-fobs

Temporary Codes

: 10 limit

One Time service code

: 10

Anti-tamper

: Red-warning light stays on for 60 seconds after 3 consecutive invalid code entries

Mechanical Key Bypass

: Standard on all units

Door Preparation

: Standard ANSI A115 Series Prep, optional by adding additional 5/8” through-bolt hole to add

stability to the lock and increase security.

Strike Plate

: ANSI Standard 115.3. Square corner, 1-1/8 x 2-3/4 inch T strike with 1-1/4 lip-to-center dimension.

Latch

: 2 3/4 inch backset standard (2 3/8 inch backset optional), solid brass with 1/2-inch throw 1-inch diameter bore is

required.

Materials

: Zinc Alloy

Temperature

: 0°F-120°F (-18°C-50°C)

Exposure

: Limited

direct

rain or water conditions.

Accessibility Standard

: Meets ADA standards (Americans with Disabilities Act)

Lock Back Time

: 1 – 25 seconds (default is 5 seconds)

Working Voltage

: 4.8-6.4V

Low Battery Warning

: 4.8V or lower

Door Thickness

: 1 3/8" to 2"

Keyway

Schlage C6 – (IC or Best compatible available as extra cost option for E5 only as handle option E5ICHDL.)

Summary of Contents for Eternity 4

























































Search results

Summary of Contents for Eternity 4

Reviews:

Brands by name

Popular brands

Access Control Solutions Eternity 4, Owners Manual And Software Manual

Search results

Summary of Contents for Eternity 4

Reviews:

Brands by name

Popular brands