AC&NC JetStor SAS 780JH JBOD Subsystem User Manual Download Page 46 | Manualshive

Page: 46 / 54

background image

80 Bays SAS to SAS/SATA JBOD Subsystem

46

User Manual

Chapter 4 Maintenance

4.1 Upgrading the JBOD Controller Firmware

IMPORTANT: Before upgrade the JBOD firmware, please shut down
server first or make sure no array setting on the JBOD disks. The
new Firmware will effective after JBOD power cycle.

NOTE: Upgrading the firmware must be done from Master JBOD
Controller (JBOD Controller 1) if the JBOD Subsystem has redundant
JBOD Controllers.

The JBOD subsystem’s factory default password is set to 00000000.

Steps:

1.

Used RS-232 Port (Phone jack to DB9) link SAS JBOD, in command line please type
“system upgrade”, than press “Enter”.

«
...
44
45
46
47
48
...
»

Summary of Contents for JetStor SAS 780JH JBOD Subsystem























































Reviews:

No comments

Related manuals for JetStor SAS 780JH JBOD Subsystem

Brand: Yamaha Pages: 3

Brand: US Robotics Pages: 36

IronKey EMS H350 Enterprise

Brand: DataLocker Pages: 23

Brand: Badger Basket Pages: 6

BARRACUDA 7200.10 ST3160215AS

Brand: Seagate Pages: 2

Brand: OpenEye Pages: 101

Brand: Magnusson Pages: 18

Brand: Excel Pages: 2

Brand: ADDC Pages: 26

Brand: WiebeTech Pages: 8

Brand: Craftsman Pages: 56

XI2000 Series XI-316R

Brand: Advanced Industrial Computer Pages: 2

Brand: Fantom Drives Pages: 10

Brand: Fantom Drives Pages: 160

Brand: TyeDee Bin Pages: 2

Brand: Clarke Pages: 4

Brand: Clarke Pages: 20

Brand: uRAGE Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands