background image

AIR FILTER CLEANING

Changing your air filter on a regular basis prevents many problems. Dirty air filters will affect 
the performance and the longevity of your unit. It is recommended that air filters be cleaned 
every three (3) months. 

To access and clean the filter:

CARE AND CLEANING

Take notice of the following items before cleaning your Livo indoor wall unit.

• To avoid electric shock or injury, do not attempt to clean the unit unless it has been turned 

off and the indoor and outdoor units have been disconnected from the main power supply.

• Do not wash the unit with water; this may cause an electric shock.

• During cleaning, be sure to use a stable and safe standing platform.

FRONT PANEL CLEANING

Wash the front panel using warm water and mild detergent with a soft cloth or soft brush.

NOTE:

Do not use bleach,abrasives or water above 110°F (45°C) as it may cause 

discoloration or damage to the surface of the unit.

1. Open Front Panel

Firmly grasp both sides of the front panel and pull upward 
to about 60 degree angle. (NOTE: do not force panel open).

2. Remove Filter

Remove the filter as indicated in the figure at right.

3.  Clean Filter

Use vacuum to clean the filter. 
When the filter is very dirty, use warm water (below 110

°F)

to clean it, and then dry filter before replacing.

4. Reinstall Filter

Reinstall the filter and then close the panel cover tightly.

WARNING

9

Summary of Contents for AWH30LB-D3DNA3D/I















Reviews: