background image

Absco Industries

Assembly Instruction Manual

ABSCO SIGNATURE GAZEBO

MODEL: ADGAZEBO33

3.11m W x 3.11m D x 2.60m H

Model: ADGAZEBO33

21/09/23

1.00

7  

 

 

A. Check the foam core is flush with the top and 

bottom skins. If it bulges out, safely trim flush with 

a Stanley knife.

B. Check if the steel bottom skin corner is bent 

down below the bottom face. Bend it up with 

pliers.

C. To increase weather protection turn up the 

pans 15 degrees with a turn up/down tool or 

equivalent as shown. (Non gutter end only)

Familiarize yourself with the weight and orientation 

of the 

AD1

 panel before lifting.

The panel end with ‘top skin’ overhang & sticker 

must go to the rear.

The ‘bottom skin’ has a protective plastic coating, 

this can be peeled off just before lifting.

Remember to lift and place 

do not slide

, this can 

scratch the panel.

4. 

Safely position the first panel on top of the 

frame - all the way to the left.

The steel ‘top skin’ will sit over the rear flashing.

5. 

Adjust so it’s butted up against the rear trim 

and

 the side of the ‘top skin’ is flush with the end 

of the flashing.

6. 

In the pan,

 

fasten panel to rear beam with a tek 

14 x 125 mm 

FAST104.

Don’t over-tighten and crush the panel.

For further screw position detail see next page.

7. 

Check for consistent overhang along side 

beam - adjust if required.

Fasten with a tek 14 x 125 mm 

FAST104

 at the 

midpoint of side beam.

8. 

In the pan

fasten to front beam with another a 

tek 14 x 125 mm 

FAST104

.

ATTACH REAR FLASHING

1. 

Place the rear flashing 

TR35

 along the rear 

beam as pictured.

Align side shown to be flush with the exterior of 

the beam.

2. 

Overhang the left side of by 

130

 mm.

3. 

Fasten flashing to top of beam with 4 evenly 

spaced pop rivets 

FAST102.

FLUSH

Front

Rear

125

1

3

2

FLUSH

Front

Rear

7

6

8

REAR VIEW - Aligning the first panel

5

Rear flashing

Rear beam

ROOF PANELS

Summary of Contents for SIGNATURE ADGAZEBO33















Reviews: