background image

IMPORTANT 

1. Manufacturer’s Disclosure

This warranty against defects shall not apply in the following situations:

 

A) Where the product is not assembled in accordance with the instructions provided in the product kit;

 

B) Where the product is used to store corrosive materials such as fertilizer, chlorine etc;

 

C) The warranty does NOT cover damage caused by storms, wind, rain, snow or poor foundations;

 

D) This warranty does not apply to surface deterioration of panels caused by ‘Swarf’ (Tiny particles of 
steel debris left from cutting, grinding or drilling operations) that has not been removed after building 
construction.

 

2. Notes
This product is weatherproof to a certain level; however driving windy rain may cause the product to leak. 
Condensation may also occur in some weather conditions such as extreme heat or cold. The product 
should only be used for storing items such as gardening equipment and should not be used for articles 
that may be prone to damage if they come into contact with moisture.

3. Major Defects
If the manufacturer is satisfi ed that the defect is a major defect, the purchase price may be refunded in lieu 
of providing a replacement product or repairing the product. 

This warranty is provided in addition to other rights and remedies you have under law:  Our goods come 
with guarantees which cannot be excluded under the Australian Consumer Law.  You are entitled to 
replacement or refund for a major failure and to compensation for other reasonably foreseeable loss or 
damage.  You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable 
quality and the failure does not amount to a major failure. 

If you do not wish to register your warranty online, complete the below form and email, fax or 

post this form back to Absco, along with a copy of your proof of purchase.

NAME:

STREET ADDRESS:  

 

 

 

 

 

     POSTAL / ZIP CODE:

STATE / CITY / PROVINCE / REGION: 

 

 

 

 

 

COUNTRY:

SHED TYPE/CODE:

ORDER NO:

DATE OF PURCHASE:

EMAIL ADDRESS:

DATE REGISTERED:

2

Summary of Contents for 2308WBCK































Reviews: