ABSCO SHEDS 2308WBCK Manual Download

Page: 2 / 30

Absco Industries

Assembly Instruction Manual

ABSCO BIN COVER

MODEL: 2308WBCK

2.27m W x 0.85m D x 1.15m H

Model: 2308WBCK

1.1

21/09/2022

GENERAL INSTRUCTIONS

• Before commencing any assembly, read through these instructions in detail to gain a thorough

understanding of assembly methods and associated details.

• Unpack the carton and carefully identify and check off all the parts against the parts described

and illustrated on "COMPONENTS PACKING LIST" pages.

SITE PREPARATION

• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately

illustrated on “FINAL CONSTRUCTION” page.

TOOLS REQUIRED

SAFETY NOTES

• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and

safety glasses if drilling holes. Sensible shoes are highly recommended.

• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is

completed.

• It is highly recommended to erect the shed with two or more people.
• Do not sit, stand or walk on the roof of your shed.

RECOMMENDED

5/16” Hex driver bit

Hammer drill

Shifter

10mm metal drill bit

10mm masonry drill bit

Pop riveter

Tinsnips

Cordless drill

4mm drill bit

Summary of Contents for 2308WBCK































Search results

Summary of Contents for 2308WBCK

Reviews:

Related manuals for 2308WBCK

Brands by name

Popular brands

ABSCO SHEDS 2308WBCK, Manual

Search results

Summary of Contents for 2308WBCK

Reviews:

Related manuals for 2308WBCK

Brands by name

Popular brands