ABSCO SHEDS 2308WBCK Manual Download Page 25

Page: 25 / 30

Absco Industries

Assembly Instruction Manual

ABSCO BIN COVER

MODEL: 2308WBCK

2.27m W x 0.85m D x 1.15m H

Model: 2308WBCK

1.1

21/09/2022

LID PROPS & CORNER BRACES

Channel

61PR

goes on the right

side and

61PL

goes on the left.

Align the existing pivot hole

with the hole in the end of the
channel and fasten with a screw
as pictured.

Repeat for the other side.

When not in use the lid prop will
rest on the 25 mm screw.

Measure down 25 mm and

make a 4mm hole in the pan of
the side wall.

From the outside poke a 25

mm long M4 screw FAST047
through from outside and fasten
with a hex nut.

Repeat this for the other side.

Position the corner brace as

pictured, on top of the front and
side wall.

Check walls are square and

then fasten with four pop rivets
FAST009 through the brace holes
Predrill into the top channels
with a 3mm drill bit DRILL before
riveting.

Repeat for the other side.

61PR

61PL

Pivot
hole

61PR

Side wall

Lid prop

Prop rest

Summary of Contents for 2308WBCK































Search results

Summary of Contents for 2308WBCK

Reviews:

Related manuals for 2308WBCK

Brands by name

Popular brands

ABSCO SHEDS 2308WBCK, Manual

Search results

Summary of Contents for 2308WBCK

Reviews:

Related manuals for 2308WBCK

Brands by name

Popular brands