Abit IS7 User Manual Download Page 79

Page: 79 / 110

BIOS Setup

3-25

All Voltages, Fans Speed and Thermal Monitoring:

These unchangeable items list the current status of the CPU and environment temperatures, fan speeds,
and system power voltage.

NOTE:

The hardware monitoring features for temperatures, fans and voltages will occupy the I/O

address from 294H to 297H. If you have a network adapter, sound card or other add-on cards that might
use those I/O addresses, please adjust your add-on card I/O address to avoid using these addresses.

3-9. Load Fail-Safe Defaults

This option loads the BIOS default values for the most stable, minimal-performance system operations.

3-10. Load Optimized Defaults

This option loads the BIOS default values that are factory settings for optimal-performance system
operations.

3-11. Set Password

This option protects the BIOS configuration or restricts access to the computer itself.

3-12. Save & Exit Setup

This option saves your selections and exits the BIOS setup menu.

3-13. Exit Without Saving

This option exits the BIOS setup menu without saving any change.

User’s Manual

Summary of Contents for IS7















































































































Search results

Summary of Contents for IS7

Reviews:

Related manuals for IS7

Brands by name

Popular brands

Abit IS7, User Manual

Search results

Summary of Contents for IS7

Reviews:

Related manuals for IS7

Brands by name

Popular brands