background image

13 

After parking the machine, remove the ignition key and lock 
the side doors with the workshop key to prevent 
unauthorised access. (        -        ). 

5.2   Sweeping system 

5.2.1  Sweeping wet materials 

ATTENTION!  –  Switch  off  the  fan  when 
sweeping wet refuse. 
This  possibly  will  cause  damage  to  the  the 
dust filter! 

5.2.2   Height

 

adjustment of the sweeping rollers 

Your sweeper is equipped with the Tandem Roller Flex 
System (TRS-Flex) and automatic lowering of the sweeping 
roller. The sweeping rollers adapt to the ground, which 
means there is no need for height adjustment. Nevertheless, 
this may become necessary if the rollers are worn or 
adjusted to a certain maximum sweeping pattern. Lift up the 
left side door first. You can raise or lower the max. low point 
by turning the adjusting screw  (         ). Only adjust this when 
the machine is switched off. 

5.2.3 Operation of the sweeper roller drive 

Press the switch to set the sweeping rollers to position I. 
The sweeping rollers can be operated separately from the 
operation of the side brush. The engine must be running for 
operation. 

ATTENTION! – Always wear face masks and 
seat belts when sweeping.  

Summary of Contents for STR1800 LPG


























Reviews: