abco STR1800 LPG Operating Manual Download Page 16 | Manualshive

Page: 16 / 25

background image

17

5.2.7 Operation of the side brush drive

Press the switch to set the side brush to position I. The side
brush can be operated separately from the operation of the
sweeping rollers. The side brush retracts automatically
when switched on. The engine must be running for
operation. Turn the switch to the 0 position to switch it off.

ATTENTION! – Always wear a face mask and
seat belt when sweeping.

5.2.8 Dismantling the side brush

ATTENTION! – Wear gloves, goggles and a
face mask during assembly. Loose parts must
be secured.

«
...
14
15
16
17
18
...
»

Summary of Contents for STR1800 LPG


























Reviews:

No comments

Related manuals for STR1800 LPG

KX-TG2248S - 2.4 GHz Digital Cordless Phone Answering...

Brand: Panasonic Pages: 68

Brand: JUKI Pages: 5

Brand: Neopost Pages: 6

Brand: Toyota Pages: 39

Brand: Kärcher Pages: 237

Brand: Oki Pages: 32

Brand: Janome Pages: 51

Brand: GBC Pages: 74

MEMORYCRAFT 300E

Brand: Janome Pages: 48

Brand: Antari Pages: 12

Brand: JB Systems Pages: 14

Brand: Singer Pages: 67

KM 70/30 C Bp Adv

Brand: Kärcher Pages: 147

Brand: Baby Lock Pages: 33

Advolution UHR 70-1700

Brand: Nilfisk-Advance Pages: 32

LT5-H7600-D-N Series

Brand: Unicorn Pages: 55

Brand: JUKI Pages: 108

Brand: Singer Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands