background image

22 

ATTENTION  -  The  sweeper  may  not  be 
cleaned  using  high-pressure  or  water  jet,  as 
these  can  cause  damage!  There  is  a  danger 
of short circuit or other serious damage! 
Do not use aggressive cleaning agents!  

ATTENTION - Personal protective equipment 
in the form of goggles, breathing protection 
and  gloves  must  be  worn  for  interior  and 
exterior cleaning of the sweeper!  

To  clean  the  machine  interior,  the  side  cover  must  be 
opened  and  the  seat  cover  folded.  Use  a  dry  cloth  for 
cleaning  and  blow  through  the  machine  with  compressed 
air. Subsequently close the main cover properly once again. 
For  the  exterior  cleaning  of  the  sweeper,  use  compressed 
air and/or a cloth or a wash mitt moistened with warm water 
or a mild detergent solution. 

6.2     General cleaning and maintenance 

instructions 

ATTENTION - For safety reasons, all cleaning 
and  maintenance  work  may  only  be  carried 
out when the machine is switched off! To do 
so,  remove  the  key  from  the  device! Failure 
to do so may result in serious injury! 

For cleaning and maintenance intervals, please refer to the 
service  indicator  (see  chapter  4.3.2.3)  or  the  maintenance 
manual!  All  service  and  maintenance  work  must  be 
performed  by  a  qualified  technician!  If  necessary,  a 
Stolzenberg  dealer  can  be  contacted  at  any  time!  You  can 
find  the  relevant  dealer  or  service  technician  for  your 
machine on the manufacturer website! 

5.5   Fuse box 

No. 

Consumer

 

Fuse in amps 

[A] 

Fan oil cooler (not shown)

 

20 A 

Fuel gauge, horn, front lights 

5 A 

All-round light

 

1 A 

Vibrator, fan (dust extractor) 

30 A 

Side brush, sweeping rollers, 
high-dumping system UP/DOWN 

20 A 

Tipping engine 
(high-dumping system) 

30 A 

Main fuse (all circuits) 

40 A 

 

 Cleaning and maintenance 

6

 

The regular maintenance of the sweeper serves to preserve 
the  machine,  its  components  and  the  sweeping  result.  If 
performed 

regularly, 

the 

subsequently 

described 

maintenance  work  can  extend  the  lifetime  of  the 
equipment! 

6.1   Safety instructions for cleaning and 

maintenance 

Summary of Contents for STR1800 LPG


























Reviews: