abco STR1800 LPG Operating Manual Download Page 11 | Manualshive

Page: 11 / 25

background image

12

5.1.2 Drive System

The machine advances by pressing the right-hand drive
pedal.

The machine reverses by pressing the left-hand drive pedal.

Ensure that the parking brake is released. Do not apply the
brake while driving.

5.1.3 Parking the sweeper

Park the machine on dry and level ground (without slope).
Apply the parking brake ( ). ).
Secure the machine additionally with chocks ( - ).
They can be found inside the machine.

Regulate the rpm of the engine by using the throttle lever.

«
...
9
10
11
12
13
...
»

Summary of Contents for STR1800 LPG


























Reviews:

No comments

Related manuals for STR1800 LPG

Brand: Janome Pages: 4

Brand: Janome Pages: 52

Bernette 340 deco

Brand: Bernina Pages: 2

Brand: T-COM Pages: 6

WERTARBEIT N 656D Free Arm

Brand: W6 Pages: 102

3001 Silent Drive

Brand: ProForm Pages: 16

Brand: PowerBoss Pages: 52

Brand: JUKI Pages: 20

Brand: Olivetti Pages: 269

Decor Excel 2 5024

Brand: Janome Pages: 41

Brand: Tennant Pages: 35

Brand: Tennant Pages: 41

Brand: Tennant Pages: 84

Brand: Tennant Pages: 95

Brand: Tennant Pages: 70

Brand: Chauvet Pages: 17

Brand: Yamato Pages: 46

Brand: Hilti Pages: 280

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands