background image

15

16

The Receiver displays your blood glucose results when the check is 

complete . If Progress Tones are on, you also hear a chime-like Progress 

Tone when results appear .
This screen displays your blood glucose result . Press Home to return to 

the Home screen .
Note: 

Measurements are accurate between 5 ° to 40 °C (40 ° to 104 °F). If the 

temperature is out of range, the Receiver displays the

   

symbol with your 

glucose reading.

Discard the test strip and lancet

•  Test strips may be used only once . Discard used test strips in a 

sealable container such as a sharps container to avoid contact with 

biohazards .

Your blood glucose results
Work with your healthcare team to determine the low and high values 

for your blood glucose target range . If you get results below or above 

your target range and do NOT have symptoms of hypoglycaemia or 

hyperglycaemia, repeat the test . If you have symptoms or continue to 

get results that are low or high, follow the treatment recommended by 

your healthcare team .

CAUTION: Low or high glucose readings can indicate a potentially 

serious medical condition .

If Low appears on your Receiver, your result is lower than 20 mg/dL 

(1 .1 mmol/L) . If you have symptoms of low blood glucose (for 

example: weakness, sweating, nervousness, headache or confusion), 

follow your healthcare team’s recommendations for 

treating severe hypoglycaemia . If you do not have 

any symptoms, wash and dry your hands and repeat 

the blood glucose check on your finger with a new 

test strip . If you receive a second Low result, follow 

your healthcare team’s recommendations for 

treating severe hypoglycaemia .

If High appears on your Receiver, your result is higher than 500 mg/dL 

(27 .8 mmol/L) . If you have symptoms of high blood glucose (for 

example: fatigue, thirst, excess urination or blurry 

vision), follow your healthcare team’s 

recommendations for treating hyperglycaemia . If 

you do not have any symptoms, wash and dry your 

hands and repeat the blood glucose check on your 

finger with a new test strip . If you receive a second 

High result, follow your healthcare team’s 

recommendations for treating severe 

hyperglycaemia .

GLUCOSE READING

Control Solution =  No

Home

Low

GLUCOSE READING

Control Solution =  No

Home

High

Notes: 

•  Use a new sterile lancet each time. NEVER use a lancet or lancing 

device for more than one person.

•  Follow instructions for your lancing device.

Apply blood sample and wait for results
1.  
Gently apply blood to ONLY ONE 

sample area of the test strip . Only a 

very tiny drop of blood is needed .

Note: 

Do NOT apply blood to both 

sample areas of the test strip. If this 
happens, discard the test strip.

2.  Watch the Receiver Display . When enough blood is applied, the 

Receiver shows a circle of 4 arrows 

  while it measures the blood 

glucose . If Progress Tones are on, you also 

hear a two-note Progress Tone .

Note: 

If needed, you have up to 60 seconds 

to add blood to the same sample area of the 
test strip.

Test Strip 

Sample Area

GLUCOSE READING

Control Solution =  No

Home

101

mg/dL

101 mg/dL = 5.6 mmol/L

Calibrating

Calibrating is the process the FreeStyle Navigator II System uses to 

match your interstitial fluid glucose readings with your blood glucose 

readings . You need to calibrate the system by checking your blood 

glucose at approximately 1, 2, 10, 24 and 72 hours after Sensor 

insertion .

•  When the system is ready to be calibrated, it 

prompts you to “Check your BG to calibrate” 

and emits an audible alarm based on your 

settings . You will also see a blood drop 

  icon  on the Home screen . To calibrate the 

system, perform a blood glucose check .

Note: 

If your system alarms are turned off, you 

will not see the “Check your BG to calibrate” 
screen or hear audible alarms.

•  See the Expert Guide for more information 

on performing and troubleshooting 

calibrations .

•  There is a time window in which each 

calibration needs to be completed called a 

grace period . If you do not calibrate before 

the grace period ends, the continuous 

glucose results are no longer displayed and the glucose alarms 

become inactive . Your Sensor remains active . If you missed the grace 

period, simply perform a blood glucose check at any time you see 

the blood drop    icon to continue the calibration process; this 

resumes continuous glucose monitoring .

OK

TIME TO CAL

Check your BG to
calibrate.

117

mg/dL

320

180

40

12 May 2012

Graph

14:30

Menu

117 mg/dL = 6.5 mmol/L

mmol/L

18

10

2

Blood Drop Icon

ART22683-101_rev-B.indd   15-16

1/7/15   11:43 AM

Summary of Contents for FreeStyle Navigator II






















Reviews: