manualshive.com logo in svg

ABB TZIDC, Operating Instructions Manual

Share
Download
ABB TZIDC Operating Instructions Manual Download Page 3

 

Contents

 

42/18-84-EN 

TZIDC, TZIDC-110, TZIDC-120 

3 

 

1

 

Safety.............................................................................................................................................................6

 

1.1

 

General information and notes for the reader ................................................................................................6

 

1.2

 

Intended use...................................................................................................................................................6

 

1.3

 

Target groups and qualifications ....................................................................................................................7

 

1.4

 

Warranty provisions........................................................................................................................................7

 

1.5

 

Plates and symbols ........................................................................................................................................8

 

1.5.1

 

Safety-/ warning symbols, note symbols.................................................................................................8

 

1.5.2

 

Name plate..............................................................................................................................................9

 

1.6

 

Transport safety information...........................................................................................................................9

 

1.7

 

Storage conditions..........................................................................................................................................9

 

1.8

 

Installation safety information.......................................................................................................................10

 

1.9

 

Safety information for electrical installation..................................................................................................10

 

1.10

 

Operating safety information ........................................................................................................................10

 

1.11

 

Returning devices.........................................................................................................................................11

 

1.12

 

Integrated management system...................................................................................................................11

 

1.13

 

Disposal........................................................................................................................................................12

 

1.13.1

 

Information on WEEE Directive 2002/96/EC (Waste Electrical and Electronic Equipment).................12

 

1.13.2

 

RoHS Directive 2002/95/EC .................................................................................................................12

 

2

 

Ex relevant safety instructions .................................................................................................................13

 

3

 

Design and function...................................................................................................................................14

 

4

 

Mounting .....................................................................................................................................................15

 

4.1

 

Operating conditions at installation site........................................................................................................15

 

4.2

 

Mechanical mount ........................................................................................................................................15

 

4.2.1

 

General .................................................................................................................................................15

 

4.2.2

 

Mounting on linear actuators.................................................................................................................17

 

4.2.3

 

Mounting on rotary actuators ................................................................................................................21

 

5

 

Electrical connections ...............................................................................................................................24

 

5.1

 

Screw terminal assignments ........................................................................................................................25

 

5.2

 

Jumper configuration on mainboard (TZIDC-120 only)................................................................................26

 

5.3

 

Cable entry ...................................................................................................................................................27

 

5.4

 

Setting the mechanical feedback .................................................................................................................27

 

5.4.1

 

Mechanical position indicator................................................................................................................27

 

5.4.2

 

Mechanical digital feedback with proximity switches ............................................................................28

 

5.4.3

 

Mechanical feedback with micro switches for 24 V ..............................................................................28

 

6

 

Pneumatic connection ...............................................................................................................................29

 

7

 

Commissioning ..........................................................................................................................................31

 

7.1

 

TZIDC ...........................................................................................................................................................31

 

7.1.1

 

Operating modes...................................................................................................................................32

 

7.1.2

 

Sample parameters...............................................................................................................................33

 

7.2

 

TZIDC-110 / TZIDC-120...............................................................................................................................35

 

7.2.1

 

Operating modes...................................................................................................................................36

 

7.2.2

 

Sample parameters...............................................................................................................................37

 

8

 

Maintenance................................................................................................................................................38

 

8.1

 

Functional check for emergency shutdown module.....................................................................................39

 

9

 

Specifications .............................................................................................................................................40

 

9.1

 

TZIDC ...........................................................................................................................................................40

 

9.1.1

 

Input ......................................................................................................................................................40

 

Summary of Contents for TZIDC

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands