manualshive.com logo in svg

ABB TZIDC, Operating Instructions Manual

Share
Download
ABB TZIDC Operating Instructions Manual Download Page 40

Specifications 

 

40 

TZIDC, TZIDC-110, TZIDC-120 

42/18-84-EN 

 

 

9 Specifications 

 

 

Change from one to two columns 

 

9.1 

TZIDC 

 

 

9.1.1  Input 

 

 

Setpoint signal (two-wire technology) 

Nominal range 

4 ... 20 mA 

Split range configuration between  

20 ... 100 % 

 

of the nominal range 

Max. 50 

mA 

Min. 3.6 

mA 

Starting at 

3.8 mA 

Load voltage at 20 mA 

9.7 V 

Impedance at 20 mA 

485 

Ω

 

 

Digital input 

 

Control voltage 

0 ... 5 V DC  
logical switching state "0" 

 

11 ... 30 V DC  
logical switching state "1" 

Current 

max. 4 mA 

 

 

9.1.2  Output 

 

 

Compressed air output 

 

Range 

0 ... 6 bar (0 ... 90 psi) 

Air capacity 

5.0 kg/h = 3.9 Nm3/h = 2.3 sfcm 

 

at 1.4 bar (20 psi) supply pressure 

 

13 kg/h = 10 Nm3/h = 6.0 sfcm 

 

at 6 bar (90 psi) supply pressure 

Output function 

For single or double-acting 
actuators, air is vented from 
actuator or actuator is blocked in 
case of (electrical) power failure 

Shut-off values 

End position 0 % = 0 ... 45 % 

 

End position 100 % = 55 ... 100 % 

 

Digital output (control circuit to DIN 19234 / NAMUR) 

Supply voltage 

5 ... 11 V  DC 

Current > 0.35 mA … < 1.2 mA 

Switching state logical "0" 

Current > 2.1 mA 

Switching state logical "1" 

Effective direction (configurable) 

normally logical "0" or logical "1" 

 

 

 

 

9.1.3  Travel 

 

 

Rotation angle 

 

Used range 

25 ... 120° (rotary actuators, 
optional 270°) 

 

25 ... 60 ° (linear actuators) 

Travel limit 

Min. and max. limits, freely 
configurable between 
0 ... 100 % of total travel (min. 
range > 20 %) 

Travel time prolongation 

Range of 0 ... 200 s, separately 
for each direction 

Dead band time limit 

Setting range 0 ... 200 s 
(monitoring parameter for 
control until the deviation 
reaches the dead band) 

 

 

 

9.1.4  Air supply 

 

 

Instrument air 

free of oil, water and dust to DIN/ISO 
8573-1. Pollution and oil content 
according to Class 3 (purity: max. 
particle size = 5 µm, max. particle density 
= 5 mg / m

3

;  oil content: max. 

concentration = 1 mg / m

3

; pressure dew 

point: 10 K below operating temperature) 

Supply pressure 

1.4 ... 6 bar (20 ... 90 psi) 

 

 

IMPORTANT (NOTE) 

Do not exceed the maximum operating pressure of the 
actuator! 

 

Air consumption 

< 0.03 kg/h / 0.015 scfm (independent 
of supply pressure) 

 

 

 

Summary of Contents for TZIDC

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands