manualshive.com logo in svg

ABB TZIDC, Operating Instructions Manual

Share
Download
ABB TZIDC Operating Instructions Manual Download Page 24

Electrical connections 

 

24 

TZIDC, TZIDC-110, TZIDC-120 

42/18-84-EN 

 

 

5 Electrical 

connections 

 

 

 

 

DANGER! Risk of explosion! (TZIDC only) 

It is prohibited to use the integrated communication interface (LKS) in an Ex area. 
Never use the integrated communication interface (LKS) on the mainboard with a positioner 
that is being used in an explosion risk area. 

 

 

1.

Strip the wire by approx. 6 mm (0.24 inch). 

2.

To connect the signal lines, the emergency shutdown module and the proximity switches or 
micro switches, insert the wire ends from the left into the respective screw terminals and 
hand-tighten the screws (access from above). To connect a plug-in module, insert the wire 
ends from above in the appropriate screw terminals and hand-tighten the screws (access 
from the side). 

 

 

 

Fig. 15: Terminal connection diagram 

A Basic model 
B Options 

 

1

Analog input / Bus connector 

2

Digital input 

1)

 

3

Digital output 

1)

 

4

Digital feedback 

1)

 

5

Analog feedback 

1)

 

6

Proximity switches 

7

Microswitches 

8

Emergency shutdown module 

1) TZIDC only 

 

 

IMPORTANT (NOTE) 

Keep cable shields as short as possible and connect on both sides. 

 

Summary of Contents for TZIDC

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands