ABB RobotStudio 2022.1 Release Notes Download Page 28

Page: 28 / 30

RobotWare Compatibility

Supported RobotWare versions

RobotStudio works with RobotWare 5.07 and later. Please check details below. The latest supported

RobotWare version for IRC5 and OmniCore controllers is stated under Help/About in RobotStudio.

RobotWare packages can be added to RobotStudio from the RobotApps window.

RobotWare 5.05 and 5.06 Compatibility

RobotWare 5.05 and 5.06 including revisions thereof are not supported by RobotStudio 5.15 and later

versions. Please use the corresponding version of RobotStudio for managing robot controllers with any

of these RobotWare versions.

RobotWare 5.07 Compatibility

General

The location of the program pointer is not updated in the RAPID Editor during program execution.

Offline

A limitation in the versions 5.07.02, 5.07.03, and, 5.07.04 of RobotWare may cause the Virtual Controller

to System Failure state during I-start on certain computers. The problem is due to the ctrl.bin-file not

being correctly created.

Workaround:

Create an empty ctrl.bin file in the INTERNAL folder of the controller system, and then

perform a warm start.

Note:

The problem will reappear if the system is I-started. The virtual controller does not support

RobotWare 5.07.08 and RobotWare 5.07.07.

Online

FlexPendant Viewer

does not work RobotWare 5.07.

RobotWare 5.08 Compatibility

RobotWare 5.08 and its revisions of are supported with the following limitations:

Offline

RobotWare 5.08 is not supported.

Workaround:

Use RobotWare 5.08.01 or later.

RobotWare 5.10 Compatibility

RobotWare 5.10 and its revisions of are supported with the following limitations:

Offline

Starting a controller will generate internal UAS error in controller error log.

RobotWare 5.11 Compatibility

RobotWare 5.11 and its revisions of are supported with the following limitations:

Offline

Linear jogging of a robot across joint values that will cause a change of confdata may fail. For example,

if the robot is jogged linearly when joint values is passing 90 degrees for axis 1 may cause the robot to

stop or to change configuration.

28/30

Summary of Contents for RobotStudio 2022.1































Search results

Summary of Contents for RobotStudio 2022.1

Reviews:

Related manuals for RobotStudio 2022.1

Brands by name

Popular brands

ABB RobotStudio 2022.1, Release Notes

Search results

Summary of Contents for RobotStudio 2022.1

Reviews:

Related manuals for RobotStudio 2022.1

Brands by name

Popular brands