ABB ProcessMaster wafer FEM610 Series Operating Instruction Download Page 63

Page: 63 / 84

FEM610 |

PROCESSMASTER | OI/FEM610-EN REV. A

8 . . .Diagnosis / error messages

Error messages

The error messages are divided into four groups in accordance with the NAMUR classification scheme.

Errors

Error no . / Range

Text on the LCD display

Cause

Remedy

F099.042 / Electronics

ADC overrange alarm. Noise too
high. Check applicati. Call
service.

Electrode signal exceed max ADC Limits. No
flow measurement possible.

In case of an empty pipe make sure the
empty pipe detector is enabled. Make sure
actual flowrate does not exceed flow range
configured. Call Service

F098.012 / Electronics

FEB communication error. EMC
disturbance. Call ABB Service.

Defective Frontend Board or Motherboard
Hardware. Incorrect wiring between sensor
and transmitter. Wrong or no connection
between those two boards.

With integral design: Call service. With
remote design: Check for wiring fault
between sensor and remote transmitter. Call
service

F097.029 / Electronics

Coil regulation error. Check
wiring of sensor coils. Call
service

Incorrect coil wiring (terminals M1 / M2) or

Wire break / short circuit or defect of coil
drive fuse or moisture in sensor terminal box.

Check for incorrect coil wiring (terminals M1
/ M2) or Wire break / short circuit or defect

of coil drive fuse or moisture in sensor
terminal box.

F096.043 / Electronics

SIL self check alarm. Call service.

The SIL monitoring function has detected a
transmitter error.

Call service

F095.036 / Electronics

Coil isolation alarm. Call service.

Defective coil incorrect wiring (shortcut M1 /
M2 vs. GND). Flooded sensor

Call service

F094.022 / Electronics

Safety Alarm Curr. Out 31 / 32

SIL function detects error. Call
Service.

The Current Output µController detects SIL

relevant errors.

Call service

F093.032 / Electronics

Electrode short cuircit. Check
wiring of sensor electrode. Call
service.

Incorrect wiring or electrode leakage or short
cut of electrode signal lead vs. shield or
sensor flooded.

Check for incorrect wiring or electrode
leakage or short cut of electrode signal lead
vs shield or sensor flooded.

F092.033 / Electronics

Electrode open cuircit. Check
wiring of sensor electrode. Call
service.

Incorrect electrode wiring or electrode signal
lead break.

Check for incorrect electrode wiring or
electrode signal lead break.

F091.030 / Electronics

Coil wiring error. Check wiring of
sensor coils. Call service.

Incorrect coil wiring (terminals M1 / M2) or

Wire break / short circuit or defect of coil
drive fuse or moisture in sensor terminal box.

Check for incorrect coil wiring (terminals M1
/ M2) or Wire break / short circuit or defect

of coil drive fuse or moisture in sensor
terminal box.

F090.035 / Electronics

ADC RX210 com. error. Call

service.

Bad EMC environment or defective
component.

Replace electronic or Contact Service.

F088.013 / Electronics

FEB communication error. EMC
disturbance. Call ABB Service.

EMC disturbance on the signal cable. Wrong
signal cable.

Check Signal cable and connection.
Call Service.

Summary of Contents for ProcessMaster wafer FEM610 Series





















































































Search results

Summary of Contents for ProcessMaster wafer FEM610 Series

Reviews:

Related manuals for ProcessMaster wafer FEM610 Series

Brands by name

Popular brands

ABB ProcessMaster wafer FEM610 Series, Operating Instruction

Search results

Summary of Contents for ProcessMaster wafer FEM610 Series

Reviews:

Related manuals for ProcessMaster wafer FEM610 Series

Brands by name

Popular brands