ABB IRB 6660 - 130/3.1 Product Manual Download Page 181

Page: 181 / 348

4 Repair

4.3.5. Replacement of complete arm system

179

3HAC028197-001 Revision: A

rig

t 200

200

8 ABB. All righ

ts reser

ed.

8. Remove the guide pins and secure the arm

system to the base with its 24

attachment

screws and washers.

Shown in the figure

Location of arm

system on page 170

M12 x 70, tightening torque: 115 Nm.

Reused screws may be used, providing
they are lubricated as detailed in section

Screw joints on page 276

before fitting.

9. Refit the

block for calibration

and

calibration

plate axis 1

at the bottom of the frame.

xx060002734

•

A: Block for calibration

•

B: Calibration plate axis 1

10. Refit the

motor axis 1

Detailed in section

Replacement of motor,

axis 1 on page 222

11. Refit the

cabling

in the base.

Detailed in section

Replacement of cable

harness, lower end (axes 1-3) on page
147

12. Perform a

leak-down test

of the gearbox axis

Detailed in section

Performing a leak-

down test on page 142

13. Refill the gearbox axis 1 with lubricating oil.

Detailed in section

Oil change, gearbox

axis 1 on page 120

14. Recalibrate the robot.

Calibration is detailed in a separate
calibration manual, enclosed with the
calibration tools.

General calibration information is
included in section

Calibration informa-

tion

15.

DANGER!

Make sure all safety requirements are met
when performing the first test run. These are
further detailed in section

DANGER - First

test run may cause injury or damage! on
page 33

Action

Note

Continued

Summary of Contents for IRB 6660 - 130/3.1


















































































































































































































































































































































Search results

Summary of Contents for IRB 6660 - 130/3.1

Reviews:

Related manuals for IRB 6660 - 130/3.1

Brands by name

Popular brands

ABB IRB 6660 - 130/3.1, Product Manual

Search results

Summary of Contents for IRB 6660 - 130/3.1

Reviews:

Related manuals for IRB 6660 - 130/3.1

Brands by name

Popular brands