ABB IRB 640 Product Manual Download Page 97

Page: 97 / 152

Calibration

Repairs

Product Manual IRB 640

7. Confirm by pressing OK. A window like the one in Figure 21 appears.

Figure 21 The dialog box used to start updating the revolution counter.

8. Start the update by pressing OK.

If a revolution counter is incorrectly updated, it will cause incorrect positioning.
Thus, check the calibration very carefully after each update. Incorrect updating can
damage the robot system or injure someone.

9. Check the calibration as in Chapter 9.5, Checking the calibration position.

Figure 22 Calibration marks on the manipulator.

10. Save the system parameters on a floppy disk.

Cancel

Rev. Counter Updating!

Robot

The Rev. Counter for all marked axes

will be changed.

It cannot be undone.

OK to continue?

*) axis number

Summary of Contents for IRB 640

























































































































































Search results

Summary of Contents for IRB 640

Reviews:

Related manuals for IRB 640

Brands by name

Popular brands

ABB IRB 640, Product Manual

Search results

Summary of Contents for IRB 640

Reviews:

Related manuals for IRB 640

Brands by name

Popular brands