manualshive.com logo in svg

ABB IRB 640, Product Manual

Share
Download
ABB IRB 640 Product Manual Download Page 7

Installation and Commissioning

On-Site Installation

Product Manual IRB 640

5

2  On-Site Installation 

2.1  Lifting the manipulator

The following lifting instructions are valid for a “naked” robot. Whenever 
additional equipment is put on the robot, the centre of gravity can change and 
make lifting dangerous.

Never walk under a suspended load.

If the integrated lifting ears on the front cannot be reached, the manipulator must be 
reoriented to the sync position.

The best way to lift the manipulator is to use lifting straps and a traverse crane. 
Attach the straps to the integrated lifting eyes on both sides of the frame (see
Figure 2). The lifting strap dimensions must comply with the applicable standards 
for lifting. It is also possible to use two lifting devices (option) for use with a fork 
lift truck (see Figure 4).

NB!
The right lifting device, the robot seen from behind, must be removed before 
start-up, see Figure 1.

Figure 1  Lifting device that must be removed.

View from behind

Lifting device

Summary of Contents for IRB 640

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands