ABB IRB 640 Product Manual Download Page 55

Page: 55 / 152

Axis 1

Repairs

Product Manual IRB 640

2.2 Cabling axis 1

Dismounting:

Refer to foldouts 2, 2:1 and 3.

Place axis 1 in calibration position 0. Shut down the robot system with the mains

switch.

Loosen the control cable connectors in the robot base.

Loosen the covers <2/21, 22> on base cabling from the base by unscrewing screws

<2/18>.

Loosen the support rail <3/3>, screws <3/6> and remove it forwards to a position

as far away from the base cabling as possible.
Do not remove the screws!

Loosen the base cabling at the bottom of the base <3/1>.

Do not remove the screws!

Tighten all screws <3/6> again after the cabling has been removed.

To avoid that the base plate <3/2> rotates and to make dismounting and mounting

of the cabling easier.

Take out the cover <2/22> and disconnect the earth wire from the contact plate in

the base.

Loosen the base cabling at the frame, screws <2:1/25>. The screws must be

removed.

Loosen the cover over axis 1 motor, the brake release unit and the serial measure-

ment board.

Caution!

The serial measurement board is an electrostatic sensitive device.
Use a wrist strap.

Summary of Contents for IRB 640

























































































































































Search results

Summary of Contents for IRB 640

Reviews:

Related manuals for IRB 640

Brands by name

Popular brands

ABB IRB 640, Product Manual

Search results

Summary of Contents for IRB 640

Reviews:

Related manuals for IRB 640

Brands by name

Popular brands