manualshive.com logo in svg

ABB IRB 640, Product Manual

Share
Download
ABB IRB 640 Product Manual Download Page 82

Repairs

Axis 6

Product Manual IRB 640

39

7  Axis 6

7.1  Dismounting the tilt housing

Refer to foldout no. 7

Dismounting:

1.

Remove the drive unit axis 6 as described in Chapter 7.2, Replacing motor/gear axis 6

2.

Attach a hoist to the tilt housing.

3.

Dismount the upper rod in the front as described in Chapter 5.1, Replacing upper and 
lower rod.

4.

Remove covers <15> and <16> on both sides by deformation or push the covers from 
inside with thickest possible 16 mm tool. If the covers are not deformed they can be 
reused.

5.

Unscrew KM-nuts <14>.

6.

Mount tool 3HAC 2486-1 and pull out the shaft <9> on both sides.

7.

Lift the tilt housing away.

Mounting:

9.

Mount the sealings <10> in the tilt housing. Use tool 3HAC 0905-1.

10.

Mount the bearings <11> in the tilt housing. Use tool 3HAC 3437-1.

11.

Apply a little grease in the hole for the shafts. Apply grease also to both the shafts.

12.

Insert shaft <9> on the same side as the balancing unit (left side of robot as seen from 
behind).

13.

Position the distance piece 3HAC 2984-1 between the upper arm and the tilt housing on 
the left side of the upper arm, seen from behind. Press the shaft <9> into position using 
tool 3HAC 3409-1 (max. pressing force 6 tons).

14.

Remove the distance piece and fit the KM nuts <14>. Tighten to a torque of 90 Nm. Use 
Loctite 243.

15.

Position shaft no. 2 in the hole and put the tool over the shaft. To set the distance between 
the tilt housing and the upper arm, put two wedges 3HAC 2347-1 in the gap. This is 
important so that the pressing force is applied over the tilt housing and the mounted 
bearing. Then press the shaft into position (max. pressing force 6 tons).

Summary of Contents for IRB 640

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands