manualshive.com logo in svg

ABB i-bus KNX ABA/S 1.2.1, Product Manual

Share
Download
ABB i-bus KNX ABA/S 1.2.1 Product Manual Download Page 25

ABB i-bus

®

 KNX 

Mounting and installation 
 

 

ABA/S 1.2.1 | 2CDC509086D0201   25 

5 

Mounting and installation 

5.1 

Information about mounting 

The installation position can be selected as required. 

To connect the device to the electrical system, use screw terminals. To connect it to the bus, use the 
supplied bus connection terminal. The terminal assignment is located on the housing. 

Once the bus and auxiliary voltages are connected, the device is ready for operation. 

 
 

Note  

The maximum permissible current of a KNX line must not be exceeded.

 

During planning and installation ensure that the KNX line is correctly dimensioned. 
The device has a maximum current consumption of <10 mA.

 

 

 

DANGER – Severe injuries due to touch voltage 

 

Feedback from differing phase conductors can produce touch voltages and lead to severe injuries. 
Operate the device only in a closed housing (distribution board). 
Disconnect all phases before working on the electrical connection. 

 

Summary of Contents for i-bus KNX ABA/S 1.2.1





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands