13 Parameter Setting and Option Overview
66
S4
D184B122U02
13
Parameter Setting and Option Overview
1) The maximum count frequency (5 kHz) may not be exceeded.
Meter Location:
TAG-No.:
Flowmeter Primary Type:
Converter Type:
Order No.:
Instrument No.:
Order No.:
Instrument No.:
Fluid Temp.:
Supply Power:
V
Hz
Liner:
Electrodes:
Excitation Frequency:
Hz
Cs:
Cz:
System Zero:
Phase:
Reference Voltage:
Parameter
Setting Range
Prog. Prot. Code:
0–9999 ( 0 = Factory setting)
Language:
German, English, French, Finish, Spanish, Italian,
Dutch, Danish, Swedish
Primary:
SE2_, SE4_; DS2_; DS4_ (
≤
DN300/12”); DS21/DS41, 10DS3111A-D (
≤
DN400/16”),
10DS3111E (
≤
DN300/12”), 10DI1425 (
≤
DN400/16”), DS4_ (
≥
DN350-400/14”-16”),
10DS3111E (
≥
DN350-400/14”-16”), 10DS3111A-D (
≥
DN500/20”),DS4_(
≥
DN500/20”),
10DS3111E (
≥
DN500/20”), 10D1422, 10DI1425 (
≥
DN 500/20”),
Meter Size:
DN 1 – 1000 / 1/25” - 40”
Q
max
:
0.05 Cal-fact to Cal-fact
Pulse Factor: 1)
pulses/unit (observe dynamic limits)
Pulse Width: 1)
ms (observe dynamic limits)
Low Flow Cutoff:
0–10 % of flow range end value
Damping:
0.2–20.0 seconds (= 1
τ
) Operating Mode: Standard, Piston Pump (0.2–3 sec)
0.07–20.0 seconds (= 1
τ
) Operating Mode: Fast
Density:
0.01 g/cm
3
– 5.0 g/cm
3
Units Q
max
:
l/s, l/min, l/g,hl/s, hl/min, hl/h, m
3
/s, m
3
/min, m
3
/h, igps, igpm, igph, mdg, gpm, gph, bbl/
s, bbl/min, bbl/h, bls/day, bls/min, bls/h, kg/s, kg/h, t/s, t/min, t/h, g/s, g/min, g/h, ml/s,
ml/min, ml/h, MI/min, MI/h, MI/day, lb/s, lb/min, lb/h, uton/min, uton/h, uton/day,
kgal/s, kgal/min, kgal/h
Units Totalizer:
l, hl, m
3
, igl, mgal, bbl, bls, kg, t, g, ml, MI, lb, uton, kgal
Max. Alarm:
%
Min. Alarm:
%
Contact Output:
F/R Signal, General Alarm, Min-Alarm, Max-Alarm, Max-/Min-Alarm, Empty Pipe
Contact Input
Ext. Totalizer Reset, Ext. Zero Return
Current Output:
0/4–20 mA, 0/2–10 mA
I
out
Low Alarm:
2-10 mA: 1.6-2 mA / 4-20 mA: 2-3.5 mA
I
out
High Alarm:
0/4-20 mA: 20-26 mA / 0/2-10 mA: 10-12 mA
Detector e. Pipe:
ON/OFF
I
out
at e. Pipe:
See I
out
Low Alarm, I
out
High Alarm
Threshold:
0–10000
Adjust e. Pipe:
1st Display Line:
Q [%]; Q [Unit]; Q [mA]; Q [m/s]; Q [Bargraph]; Totalizer; Totalizer\
→
F; Totalizer\
←
R;
Tag Number; Blank Line
2nd Display Line:
same as above
3rd Display Line:
same as above
4th Display Line:
same as above
Operating Mode:
Standard/Piston Pump/Fast
Flow Indication:
Forward/Reverse, Forward
Flow Direction:
Standard, Invers
Pulse Output:
❏
Active
❏
Passive
Communication:
❏
HART-Protocol
❏
PROFIBUS PA
❏
No
Detector empty Pipe:
❏
Yes, activated
❏
No (Meter size too small, preamplifier)
Alarm:
❏
Yes
❏
No
Ext. Input:
❏
Yes Ext. Totalizer Reset
❏
Yes Ext. Zero Return
❏
No
