ABB EasyLine EL3020 Instructions For Installation Start-Up And Operation Download Page 57 | Manualshive

Page: 57 / 136

background image

Installing the Gas Analyzer

57

Gas Connections for Limas23 with Magnos206 (Model EL3040)

Limas23: Gas Connections

13

Sample gas inlet

14

Sample gas outlet

11

Purge gas inlet for case

12

Purge gas outlet for case

Design:

1/8 NPT female thread (stainless steel 1.4305/SAE 303)
Connection of flexible tubes: Straight screwed fittings (PP) with nozzles for flexible
tubes with inside diameter = 4 mm (supplied)
Connection of pipelines: Threaded connections (not supplied)

Note:

The pressure sensor is connected internally in the outlet of the sample cell.

Magnos206: Gas Connections

1

Sample gas inlet

2

Sample gas outlet

3

not assigned

4

not assigned

Design:

1/8 NPT female thread (stainless steel 1.4305/SAE 303)
Connection of flexible tubes: straight screwed fittings (PP) with nozzles for flexible
tubes with inside diameter = 4 mm (supplied)
Connection of pipelines: Threaded connections (not supplied)

Note:

The sample gas inlet of the Limas23 is connected ex works to the sample gas inlet
of the Magnos206.

«
...
55
56
57
58
59
...
»

Summary of Contents for EasyLine EL3020









































































































































Reviews:

No comments

Related manuals for EasyLine EL3020

Brand: Kawai Pages: 70

Brand: Dallas Brass Pages: 19

Brand: jenway Pages: 50

Brand: jenway Pages: 62

Brand: Xantrex Pages: 2

Brand: Xaoc Devices Pages: 8

Brand: YOSensi Pages: 26

Brand: YOSensi Pages: 26

Brand: Gates Pages: 112

Brand: PCE Health and Fitness Pages: 11

DGX Gears XTRA Regulator

Brand: Dive Gear Express Pages: 26

Brand: A&D Pages: 24

Brand: Keithley Pages: 338

Lange ORBISPHERE 3100

Brand: Hach Pages: 47

Brand: Hanna Instruments Pages: 2

Brand: Banner Pages: 6

Blancett B220-880

Brand: Badger Meter Pages: 16

Brand: Patlite Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands