ABB AC 800M Manual Download Page 123

Page: 123 / 200

Section 2 Installation

Installing the FOUNDATION Fieldbus High Speed Ethernet Interface,

3BSE036351-510 A

123

Installing the FOUNDATION Fieldbus High Speed Ethernet
Interface, CI860/TP860

The CI860 is powered from the processor unit via the CEX-Bus and requires
therefore no additional external power source.

Use the following procedure to install the CI860/TP860:

Mount the unit onto the DIN-rail, see

Mounting AC 800M Units onto DIN-Rail

on page 65 and

Installing the PM86x/TP830 Processor Unit in Single

Configuration

on page 78.

Connect the Ethernet twisted pair cable to the COM connector on the
baseplate.

Connect the other end of the Ethernet cable to Ethernet network via standard
Ethernet components.

Please make sure to meet the FOUNDATION Fieldbus High Speed Ethernet
specification of the network and the network devices.

Ethernet Twisted Pair Connection

The Ethernet twisted pair is connected via the RJ45 connector located on TP860.
For a description of the connector see

Table 5

on page 84.

Summary of Contents for AC 800M









































































































































































































Search results

Summary of Contents for AC 800M

Reviews:

Related manuals for AC 800M

Brands by name

Popular brands

ABB AC 800M, Manual

Search results

Summary of Contents for AC 800M

Reviews:

Related manuals for AC 800M

Brands by name

Popular brands