ABB A145-H66 Page 141 Original Operation Manual Download

Page: 141 / 142

Operation Manual / 4 Product description / A130-M.. - A145-M..

Tables

HZTL4031_EN

Revision F

August 2017

Tables

Table 1: Related documents .......................................... 3

Table 2: Weights of turbochargers A130-M.. – A145-
M.. ...................................................................................... 8

Table 3: Requirements for threaded rods ................ 14

Table 4: Tightening torques for standard nuts....... 16

Table 5: Pressure screw tightening torques............ 18

Table 6: Lubricating oil pressure, oil inlet ............... 25

Table 7: Lubricating oil temperature at the inlet ... 26

Table 8: Lubricating oil temperature at the outlet 26

Table 9: Tightening torque (86505).......................... 30

Table 10: Expected replacement intervals ............... 37

Table 11: Maintenance table ....................................... 40

Table 12: Parameters for wet cleaning of com-
pressor ........................................................................... 44

Table 13: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 47

Table 14: Wet cleaning of turbines, parameters .... 48

Table 15: Value table for soaking .............................. 56

Table 16: Malfunctions when starting – Delayed
start-up .......................................................................... 59

Table 17: Malfunctions when starting – Vibrations 59

Table 18: Malfunctions when starting – Rubbing of
rotating parts................................................................ 59

Table 19: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 60

Table 20: Malfunctions during operation – Speed re-
duces............................................................................... 60

Table 21: Malfunctions during operation – Speed in-
creases ........................................................................... 60

Table 22: Malfunctions during operation – Exhaust
gas temperature too high ........................................... 61

Table 23: Malfunctions during operation – Charge air
pressure too low............................................................ 61

Table 24: Malfunctions during operation – Charge air
pressure too high ......................................................... 62

Table 25: Malfunctions during operation – Engine
performance losses ..................................................... 62

Table 26: Malfunction – Turbocharger pumping.... 63

Table 27: Malfunction – Sporadic surge blows ........ 63

Table 28: Malfunctions when stopping – Runout
noises ............................................................................... 64

Table 29: Malfunctions when stopping – Runout
time too short ................................................................ 64

Table 30: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 65

Table 31: Malfunction of the speed measurement
system – Measured speed too high ........................... 65

Table 32: Malfunction of the speed measurement
system – Measured speed too low............................. 65

Table 33: Swivel lifting eyes ......................................... 68

Table 34: Ring nuts to be used.................................... 69

Table 35: Weights of assemblies ................................ 70

Table 36: 3 press-off screws........................................ 75

Table 37: 6 press-off screws........................................ 76

Table 38: Permissible clearances A and B ................. 84

Table 39: Permitted nozzle ring compression PD ... 85

Table 40: Tightening torque (51007) ......................... 88

Table 41: Tightening torque (79041).......................... 90

Table 42: Tightening torque (72011) .......................... 91

Table 43: Permissible clearances N and R................. 92

Table 44: Tightening torque (72020) ......................... 93

Table 45: Tightening torque (51009) ......................... 96

Table 46: Tightening torques...................................... 98

Table 47: Tightening torques for insulation............. 99

Table 48: Cover plate dimensions [mm] ................. 103

Table 49: Customer spare part set 97070 .............. 107

Table 50: Spare parts list ........................................... 109

Page

111

Page

111

Summary of Contents for A145-H66















































































































































Search results

Summary of Contents for A145-H66

Reviews:

Related manuals for A145-H66

Brands by name

Popular brands

ABB A145-H66, Original Operation Manual

Search results

Summary of Contents for A145-H66

Reviews:

Related manuals for A145-H66

Brands by name

Popular brands