ABB A145-H66 Page 78 Original Operation Manual Download

Page: 78 / 142

Operation Manual / 4 Product description / A130-M.. - A145-M..

6 Periodic maintenance work / 6.3 Cleaning the turbine during opera-
tion

HZTL4031_EN

Revision F

August 2017

Fig. 23: Carrying out wet cleaning of turbines

Fulfil prerequisites.

Ensure that the water supply (01) is guaranteed.

Open the stop valve (02) and set the water volume flow V

with a flowmeter (03) (see

cleaning parameters).

Close the stop valve (02) after 10 minutes.

Wait for 10 minutes; do not change the load during this stabilisation phase.

If the cleaning result is unsatisfactory or there is water leakage, contact an ABB Turbochar-
ging Service Station.

Product

Temperature be-

fore turbine before

cleaning [°C]

Maximum temper-

ature before tur-

bine during clean-

ing [°C]

Water volume flow

[dm

/min]

Injection time

[min]

A130

350 ... 430

530

4.0

A135

350 ... 430

530

5.5

A140

350 ... 430

530

8.5

A145

350 ... 430

530

12.0

Table 14: Wet cleaning of turbines, parameters

Corresponds to a water pressure p

of 1.5 bar (overpressure compared to atmosphere)

Page

111

Summary of Contents for A145-H66















































































































































Search results

Summary of Contents for A145-H66

Reviews:

Related manuals for A145-H66

Brands by name

Popular brands

ABB A145-H66, Original Operation Manual

Search results

Summary of Contents for A145-H66

Reviews:

Related manuals for A145-H66

Brands by name

Popular brands