ABB A145-H66 Page 40 Original Operation Manual Download | Manualshive

Page: 40 / 142

background image

Operation Manual / 4 Product description / A130-M.. - A145-M..

2 Removing and Installing / 2.2 Removing the turbocharger

© Copyright 2017 ABB. All rights reserved.

HZTL4031_EN

Revision F

August 2017

Version with water cooling

CAUTION

Freezing of the cooling water in the bearing casing

If cooling water freezes in the bearing casing, this can lead to severe dam-
age.

u

For transport and storage of the turbocharger, drain the cooling water
from the bearing casing via one of the two bottom openings of the water
connections.

2.2.1

Fastening of the turbocharger

Depending on the type and version, the turbocharger can be fastened in different ways. The
appropriate procedure must be chosen to undo the connection.

Oil-cooled bearing casing (A)

u

Attach lifting gear to the suspension eye.

u

Loosen and remove nuts (E). If clamping nut (D) is present: Loosen in accordance with
chapter

Loosening the clamping nut

.

u

Positioning the turbocharger for storage

.

Water-cooled bearing casing (B)

u

Loosen and remove water connections. Close the openings of the water connections with
screw plugs.

u

Attach lifting gear to the suspension eye.

u

Loosen and remove nuts (E). If clamping nut (D) is present: Loosen in accordance with
chapter

Loosening the clamping nut

.

u

Positioning the turbocharger for storage

.

Hydraulic loosening (round special nut)

u

Attach lifting gear to the suspension eye.

u

Loosen the round special nut with a hydraulic tool according to the instructions of the en-
ginebuilder.

u

Positioning the turbocharger for storage

.

Page

10

/

111

«
...
38
39
40
41
42
...
»

Summary of Contents for A145-H66















































































































































Reviews:

No comments

Related manuals for A145-H66

Brand: NEILPRYDE Pages: 53

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

Brand: idi Pages: 20

Brand: G&G Pages: 2

Brand: H&S Pages: 46

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brand: Gait up Pages: 6

Brand: Gaiam Pages: 2

ActiveFinder One

Brand: LaserLiner Pages: 92

Brand: R&S Pages: 2677

Brand: Wacker Neuson Pages: 34

Brand: Valko Pages: 10

Brand: JBM Pages: 13

Brand: Abus Pages: 8

Brand: Keithley Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands