ABACO PCIE-5565RC Series Hardware Reference Manual Download | Manualshive

Page: 29 / 72

background image

28 PCIE-5565RC* Ultrahigh Speed Fiber-Optic Reflective Memory with Interrupts

Publication No. 500-9300875565-000 Rev. C.0

2.5 Interrupt Circuits

The RFM-5565 has a single interrupt output (INTA#). One or more events on the
RFM-5565 board can cause the interrupt. The sources of the interrupt can be
individually enabled and monitored through several registers.

The interrupt circuitry of the RFM-5565 is arranged in two tiers. The primary tier
of interrupts is enabled and monitored by the Local Configuration Register’s
INTCSR at offset $68. The sources for monitoring the primary tier interrupts
include:

1. DMA Ch 0 Done

2. Local Interrupt Input (LINTi#)

The primary tier interrupt source (1) is used during DMA cycles and must be
configured in the DMA registers.

The other primary tier interrupt source (2) is the Local Interrupt Input (LINTi#).
All secondary tier interrupts are funneled through the LINTi#. Second tier
interrupts include several operational status bits, faults, and network interrupts.
The second tier interrupts are selected and monitored through the two RFM
Control and Status Registers referred to as the Local Interrupt Status Register
(LISR) and the Local Interrupt Enable Register (LIER). For a detailed description
of these two registers

See

Section 3 • Programming

on page 32. A block diagram

of the main interrupt circuitry is shown in

Figure 2-1

on page 29.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
27
28
29
30
31
...
»

Summary of Contents for PCIE-5565RC Series









































































Reviews:

No comments

Related manuals for PCIE-5565RC Series

Brand: Gallagher Pages: 13

Brand: West Mountain Pro Pages: 36

APG8201 PINhandy 1

Brand: ACS Pages: 8

Brand: Hamlet Pages: 4

Brand: Gigabyte Pages: 44

Brand: Gainward Pages: 1

Brand: Magtek Pages: 70

Brand: Identiv Pages: 40

Brand: Gigabyte Pages: 36

Soliroc 0 778 71

Brand: LEGRAND Pages: 2

RossGear AFR-7814C

Brand: Ross Pages: 16

Brand: Ezquest Pages: 1

Brand: Broadcom Pages: 60

Brand: Nvidia Pages: 36

Brand: Nvidia Pages: 22

Brand: TAGSYS RFID Pages: 51

Wi-Fi Inventory Reader

Brand: TAGSYS RFID Pages: 36

Brand: Rosslare Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands