abaco systems SBC347A-11330001 Hardware Reference Manual Download Page 62

Page: 62 / 111

62 SBC347A 3U VPX Single Board Computer

Publication No. 500-9300527837-000 Rev. A.0

6.4 Watchdog Timer Refresh Register (0x60D)

Any write access to this register reloads the Watchdog Timer (WDT). This must be
done periodically after the WDT is enabled to keep the WDT from causing a
board reset.

Any read access returns 0x00.

6.5 Watchdog Timer Control and Status Register LS Byte (0x60E)

6.6 Watchdog Timer Control and Status Register MS Byte (0x60F)

6.7 Board ID String Registers (0x610 to 0x61A)

These read back ASCII values for “SBC347A”, as follows:

NOTE

Code should be written to read bytes until the first NULL is encountered or the last byte is reached

(0x61A).

Bits

Read/Write Description

Default

7 to 1

Read only

Reserved

0000000

Read/Write WDT enable:

1 = WDT enabled

0 = WDT disabled

Bits

Read/Write Description

Default

7 to 3

Read only

Reserved

00000

2 to 0

Read/Write WDT timeout

selection:

111 = 2 ms

110 = 32 ms

101 = 131 ms

100 = 262 ms

011 = 524 ms

010 = 2.1 s

001 = 33 s

000 = 66 s

111

Value ASCII Default

610

0x53

611

0x42

612

0x43

613

0x33

614

0x34

615

0x37

616

0x41

9x41

617 to 61A

0x00

Summary of Contents for SBC347A-11330001
















































































































Search results

Summary of Contents for SBC347A-11330001

Reviews:

Related manuals for SBC347A-11330001

Brands by name

Popular brands

abaco systems SBC347A-11330001, Hardware Reference Manual

Search results

Summary of Contents for SBC347A-11330001

Reviews:

Related manuals for SBC347A-11330001

Brands by name

Popular brands