AAT s-max D1601 Original User Manual Download Page 37

Page: 37 / 40

LED flashes

Fault Condition

Defective charging socket

Speed controller, UP/DOWN switch, plug-in contacts or supply line are defective

Circuit board fault (FET)

Circuit board fault (relay)

Motor fault

Overload

Overvoltage

Electromagnetic brake fault

Electronics fault

10x

Sensor hollow shaft fault (only if ComfortStep is activated)

Problem

Testing and troubleshooting

Unable to switch on

s-max

Is the charger connected?

Yes: Disconnect the charging cable.

Are the batteries empty?

Yes: Charge the batteries.

Is the problem still present?

Yes: Contact the manufacturer, AAT field service or the authorised dealer.

s-max is not moving

Is the safety chip for the engine immobiliser inserted?

Yes: Contact the manufacturer, AAT field service or the authorised dealer.

Battery pack doesn’t charge

Contact the manufacturer, AAT field service or the authorised dealer.

The housing of the battery pack is

damaged

Contact the manufacturer, AAT field service or the authorised dealer.

Trouble shooting

Malfunction codes

Summary of Contents for s-max D1601









































Search results

Summary of Contents for s-max D1601

Reviews:

Related manuals for s-max D1601

Brands by name

Popular brands

AAT s-max D1601, Original User Manual

Search results

Summary of Contents for s-max D1601

Reviews:

Related manuals for s-max D1601

Brands by name

Popular brands