manualshive.com logo in svg

AAT s-max D1601, Original User Manual

Share
Download
AAT s-max D1601 Original User Manual Download Page 33

33

9.2  Check the lining of the brakes and the climbing feet

i

  NOTE - Minimum thickness for brake lining = 1 mm. Should the lining be thinner or damaged, contact the  

 

manufacturer, AAT field service or authorised personnel! 

i

  NOTE - If the foot lining is worn or broken, please have both climbing feet replaced by the  

 

manufacturer, AAT field service or your authorised dealer!

Check the brake lining of the 

safety brakes regularly.

Please also check the 

climbing feet castors for 

damage on a regular basis.

9.3  Cleaning and disinfection

 WARNING - Check safety brakes after cleaning (Chapter 6.5)!

 WARNING – Do not smoke during cleaning!

 WARNING – It is important to prevent moisture from getting into the device! 

Only use moist cloths. Avoid wet cloths without fail!

 NOTE - Clean the safety brakes and the brake drums in the wheel rims weekly or after 

contamination using alcohol! Follow the hazard notes on the alcohol!

 NOTE - Keep the s-max away from sources of ignition!

 NOTE – Do not use a high-pressure cleaner!

Clean upholstery covers as 

well as all surfaces, that are 

in contact with the skin of the 

occupant after each use.

 

» Only use household 

cleaning detergents to wipe 

surfaces clean.

All other components can 

be wiped clean with a mild 

conventional household 

detergent.

 

» Follow the hazard notes on 

the detergent before each 

use!

Should you need to disinfect, 

clean it by wiping with 

 

household disinfectants 

and take note of the 

manufacturer’s specifications. 

Follow the hazard notes on 

the disinfectant before each 

use.

i

i

i

Summary of Contents for s-max D1601









































Reviews:

No comments

Brands by name

Popular brands

Load more brands