manualshive.com logo in svg

AAON SS1068, Technical Manual

Share
Download
AAON SS1068 Technical Manual Download Page 86

APPENDIX A - SAVE, LOAD, COPY SETPOINTS

86

VCC-X Operator Interface SD

Modular Service Tool Instructions

From any menu screen, 

press

 

<BALANCE-TEST>

. The 

Unit Selec-

tion Screen 

will appear requesting that you enter the unit ID number. 

Enter Unit Address

Then Press Enter

Selected Unit#: XXXX

No Communication

Enter

 the network unit ID for the controller you want to save the 

setpoints from.  Example, ‘102’ for Loop 1 / Unit 2. Then 

press

 

<ENTER>

. Once communication is established, “No Communica-

tion” will be replaced with “Press Down.” After a brief pause, 

press

 

<

>

 to get to the 

Balance - Test Screen

 shown below.

Outputs Force

Para Blocks

Save/Copy/Restore

Scroll down to the ‘Save/Copy/Restore’ option and 

press

 

<ENTER>

. 

This will take you to the Save Setpoints screen.

System Manager SD Instructions

From any Main screen, 

press

 

<SETPOINTS>

. The screen below 

will appear because this option requires passcode clearance. Only a 
Level 2 passcode can change setpoints. 

THIS ACTION REQUIRES

PASSCODE CLEARANCE

Enter Passcode: XXXX

If the correct passcode was entered, the 

Unit Selection Screen

 will 

be displayed. 

Enter Unit Address

Then Press Enter

Selected Unit#: XXXX

No Communication

Enter the Unit ID of the controller you wish to save the setpoints from 
and 

press

 

<ENTER>

. Once communication is established, “No Com-

munication” will be replaced with “Press Down.” Then

 

press

 

<

>

. 

NOTE: 

 If “No Communication” remains, it indicates a 

communication failure to the controller.

The following screen will be displayed: 

Change Setpoints
Configure Unit

Save/Copy/Restore

Scroll down to the ‘Save/Copy/Restore’ option and 

press

 

<ENTER>

.   

This will take you to the Save Setpoints screen.

   

Save Setpoints - Network Mode

From the 

Save Setpoints Screen

 shown below:

  Save Setpoints

Press Enter To Save

Press

 

<ENTER>

 and a setpoint 

fi

 le will be saved to the SD card.  

You will receive a message that the save was successful.  This 

fi

 le 

is speci

fi

 c to this controller on this loop.

Saving & Copying Setpoints

Summary of Contents for SS1068



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands