manualshive.com logo in svg

AAON SS1068, Technical Manual

Share
Download
AAON SS1068 Technical Manual Download Page 54

Zone

Zone

VCC-X SETPOINTS

    VCC-X Operator Interface SD

54

Setpoint Screen #55 -     Return Air Temperature 

Sensor Calibration - Current and Offset

VCC-X Spts ID:#

Return Sensor Cal

Current:   0.0

º

F

Offset.:   0.0

º

F

If the  Return Air Temperature Sensor is reading incorrectly, you can 
use this option to enter an offset temperature to adjust the Sensor’s 
Temperature. Line 3 will display the current Return Air Temperature 
reading. Enter a positive Sensor Calibration value in Line 4 to raise 
the Return Temperature Sensor reading or a negative value in Line 
4 to lower the Sensor reading.

Description

Minimum

Default

Maximum

Return Air Sensor 
Calibration Offset

-100.0ºF

(-55.5

º

C)

0.0ºF
(0

º

C)

100.0ºF

(55.5

º

C)

Setpoint Screen #56 -     SAT Sensor Calibration 

- Current and Offset

VCC-X Spts ID:#

SAT Sensor Cal

Current:   0.0

º

F

Offset.:   0.0

º

F

If the  Supply Air Temperature Sensor is reading incorrectly, you can 
use this option to enter an offset temperature to adjust the Sensor’s 
Temperature. Line 3 will display the current Supply Air Temperature 
Sensor reading. Enter a positive Sensor Calibration value in Line 
4 to raise the Supply Air Temperature Sensor reading or a negative 
value in Line 4 to lower the Sensor reading.

Description

Minimum

Default

Maximum

Sensor Calibration SAT

-100.0ºF

(-55.5

º

C)

0.0ºF
(0

º

C)

100.0ºF

(55.5

º

C)

Setpoint Screen #57 -     OAT Sensor Calibration 

- Current and Offset

VCC-X Spts ID:#

OAT Sensor Cal

Current:   0.0

º

F

Offset.:   0.0

º

F

If the  Outdoor Air Temperature Sensor is reading incorrectly, you 
can use this option to enter an offset temperature to adjust the 
Sensor’s Temperature. Line 3 will display the current Outdoor Air 
Temperature Sensor Reading. Enter a positive Sensor Calibration 
value in Line 4 to raise the Outdoor Air Temperature Sensor reading 
or a negative value in Line 4 to lower the Sensor reading.

Description

Minimum

Default

Maximum

OAT Sensor Calibration 

Offset

-100.0ºF

(-55.5

º

C)

0.0ºF
(0

º

C)

100.0ºF

(55.5

º

C)

Setpoint Screen #58 -    CO

2

 Sensor Calibration 

- Current and Offset

VCC-X Spts ID:#

CO2 Sensor Cal

Current:   0ppm
Offset.:   0ppm

If the CO

2

 Sensor is reading incorrectly, you can use this option 

to enter an offset reading to adjust the Sensor’s Sensitivity. Line 3 
will display the current CO

2

 Sensor reading. Enter a positive Sensor 

Calibration value in Line 4 to increase the CO

2 

Sensor reading or a 

negative value in Line 4 to lower the Sensor reading.

Description

Minimum

Default

Maximum

Sensor Calibration 

CO

2

-500.0 PPM

0.0 PPM

500.0 PPM

VCC-X Setpoint Screens

Summary of Contents for SS1068



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands